Apollo Spray Gun Spares Uk

Posted on

• • • • • • • • • FUJI PARTS & ACCESSORIES To help you navigate better through our FUJI Parts and Accessories page please take a moment to look at our Spray Gun At A Glance Reference Sheets below. Gravity Feed Gun Holder Stand #5330 This 2 piece Gravity Feed Gun Holder allows the user to fill the gravity feed Spray Gun without assistance. Rest your Fuji Gravity Spray Gun while you are refilling the cup or in-between coats. Will also fit other standard size center mounted gravity Spray Guns. Please note that this is not compatible with the 9600-G and the 7002G Spray gun. It is also not compatible with other side-mounted spray guns. Handy Gun Holder #7095 The same Handy gun holder that is used on our Turbines for your spray gun can be used as a bench mount gun holder.

Easy carry handle and Handi-Hold™ spray gun docking station. These units will carry a new Apollo Brand name ASI-HVLP and will be offered with five spray gun.

You should be able to use this with any HVLP Turbine guns. Just screw to any bench or shelf and easily rest your spray gun when not in use or when filling your cup. Fuji Spray® Cups A variety of cups available: • #2041 1QT Aluminum Cup • #2041T 1QT Aluminum Cup Teflon Coated • #2042 1QT Aluminum Cup Assembly • #9730 3oz Gravity Cup Assembly – T-Series • #9740 400cc Gravity Cup Assembly – T-Series • #9760 600cc Aluminum Gravity Cup Assembly – T-Series • #9775 1000cc Gravity Cup Assembly – T-Series • #9080 250cc Mini Cup Assembly plus 2 extra cups • #9850 400cc Gravity Cup Side Mounted GXPC • #9860 600cc Nylon Gravity Cup Assembly T-Series 2Qt. Pressure Pot Assembly Kit #5432 This Kit has everything you need to add additional material capacity using your 4-stage Fuji Spray HVLP System. Features: • Twice as much material capacity than your bottom feed spray gun, and more than three times the capacity of your gravity feed spray gun.

Apollo Spray Gun Spares UkApollo Spray Gun Spares Uk

• Specially designed pot, lid, and adapter. • No need for bulky compressor. The Fuji Spray 4-stage turbine pressurizes the 2Qt. • Ability to spray at any angle, including upside down. • Smaller profile to reach tight corners. Please note: You will need both a standard 25ft hose plus a whip hose in order to use your Fuji Spray 2Qt.

Pressure Pot. Important: If you are using model 9600-G – GXPC Spray Gun, you will also need a 9060 L-Fitting. Gravity Cup Conversion Kit #9960 This conversion kit includes a U-Tube accessory to convert any Fuji Spray Gun Bottom Feed to a Gravity style. It can also be used with other spray guns.

Includes 400cc Aluminum Gravity Cup, Stainless Steel U-Tube, Pressure Tube with Check Valve. Mini 3ozs Gravity Cup #9730 for T-75G ONLY Miniature 3ozs Gravity Cup is designed and built by Fuji Spray to meet the need for a small Touch-Up Gravity Cup for use in the Automotive field. This Cup can be used with the Fuji T-75G Gravity Spray Gun. Perfect for spraying smaller items or touch up. The 9730 model (as shown) is pressurized and comes with one 2024 Pressure Tube with Check Valve installed. Also available, the same 3ozs cup without pressurization – just a small bleeder hole on top.

This is designed for use in Spray Tanning and similar applications. Both cups feature a screw-on lid with a rubber gasket. PLEASE NOTE For side- mounted G-XPC, please refer to part #8080. #8080 is a mini 3oz Gravity Cup for side-mounted G-XPC Spray Gun ONLY Mini 3-Cup Set #9080 Complete 1/2pint (8ozs) Miniature Cup Assembly. Supplied with 2 Extra Cups and 3 Heavy-Duty lids equipped with Gaskets. This assembly is lightweight taking weight off the wrist.

The small size allows access into confined areas such as cabinets, bookshelves etc. The Cup is pressurized so the spray pattern is always perfect. You will think of many uses for these Cups – storing paints and stains. It’s great for quick color changes. Any type of touch-up work. Guitar Makers and Auto Touchup are just 2 areas where this Cup Assembly is proving to be popular.

If you are always spraying larger pieces such as kitchen cabinets, this cup set is too small for you – it would require too many fill ups to make it practical. Please note* this Cup Assembly can be used with the Fuji XPC Spray Gun as well as the New T-Series Spray. How To Uninstall Roxio Creator 9 Review on this page.

Flexible Whip Hose #2049F Lightweight 6ft. Hose is highly flexible. Couplings are made from a Glass Fiber-Reinforced Polymer. Takes weight off the wrist and the flexibility allows for effortless maneuverability of the spray gun. An added feature is that the air through the spray gun is not as hot (due to the fact the spray gun is now 6ft further from the Turbine). This often alleviates problems with fast drying lacquers (and Latex House Paint) drying too quickly. This Whip Hose features a smooth internal bore.

Please note* this hose cannot be connected to the Turbine – it is an extension hose and must only be connected to the end of the standard 25ft Hose. Caps for Cups # 9903-3 Set of 3 Plastic Lids will fit any Fuji 1qt (1000cc) cup.

Handy for storing paints. AIRCAP SETS If you own the T-Model, please check the part numbers in your User Manual (5100series). If you own the M-Model, please check the part numbers in your User Manual (7020 series). If you own the G-XPC/XPC, please check the part numbers in your User Manual (8050 series). If you own an older XT or GT-X, please check the part numbers in your User Manual (9001 series) Please review the Fuji Spray Quick Reference Sheet above to help you with your Air Cap Set selection. #2039 – Cup Parts Kit Kit includes wearable parts that you should always have on hand. Older Fuji Cups with the black-colored lid can be converted to use the 2038 Plastic Diaphragm. We have found that using this diaphragm in combination with the 2024 Pressure Tube/Check Valve, there is very little chance of the paint backup.

This kit includes 2036 gaskets. All the parts shown in the kit can be ordered separately (please see below). This Diaphragm is very effective at preventing paint entering the clear Pressure Tube. Please note* If you own a Gravity Cup you would order one of the following Gravity Cup Parts Kits: – For the 600cc Gravity Cup please order part # 2060 (600cc/1000cc Gravity Cup Parts Kit) – For the 400cc Gravity Cup please order part # 2030 (400cc Gravity Cup Parts Kit) #2024-5 Pressure Tube/Check Valves Pressure Tubes with Check Valves installed for any Fuji 1 Quart Cup Gun.

Available only in packs of 5. These Tubes also fit older Fuji Spray Guns. If clogged, Check Valve cannot be taken apart but they can be soaked in thinner for up to 30 minutes to free any blockage. Please note* For the Gravity Cup you would order 2024L-5 Pressure Tube-Long. #2036-5 Cup Gaskets The Diaphragm 2038 must be used with these Gaskets. Available only in packs of 5.

Please note* If you own a Gravity Cup you would order one of the following Gravity Gaskets: – For the 600cc Gravity Cup please order part # 9720-5 (600cc/1000cc Gravity Cup Gaskets) – For the 400cc Gravity Cup please order part # 9050-5 (400cc Gravity Cup Gaskets) #2038 – Plastic Diaphragms Tough and durable, the Diaphragms should last months (if not years) if care is taken sliding them down the Metal Fluid Tube. To remove them from the cup, grab the tab. The Air Hole in the Diaphragm should be positioned at the rear of the Cup (towards the handle). That is, unless you intend spraying upwards for any length of time. For spraying upwards, position the hole in the Diaphragm towards the front of the spray gun.

The idea is to keep the hole out of the paint as much as possible. These Diaphragms, in combination with the Pressure Tube/Check Valve, cure the problem of paint backing up the Pressure Tube. #9044-5 Paint Strainer Inexpensive Nylon Strainer fits at the end of the Metal Fluid Tube. Durable and long-lasting. Can be soaked in thinner to clean.

Sold in packs of 5. #3100 Spray Gun Cleaning Kit with Lubricant Complete 19pc Spray Gun Cleaning & Maintenance Kit with Lubricant. This is designed for all types of spray guns & equipment.

Includes an extra-long 12″ pick-up tube brush, HVLP brush, body cavity brush, detail end brush, nylon bristle parts brush, 5-pc. Micro brush set, 6-pc. Precision needle set, and spray gun lubricant. #3072 Wireless Turbine Remote Use this Turbine Remote to allow you to control the on/off of your Turbine. There is no need to walk back and forth to your Turbine anymore.

This device will work from within a frequency range of 60 feet away. Its extends the lifetime of your Turbine motor. Just plug it in. #4009-2 DIY-PRO Series and previous models Mini-Mite Turbine Filters Turbine Filters fit Semi-PRO 2™, Hobby-PRO 2™ and previous Mini-Mite Model Turbines.

Coarse Filter goes on the Right Hand Side (as seen when looking at the front of the Case) Fine Filter on the left. Please note* these Filters will not fit the Super Model or Q Model, or Platinum Models. #7224-2 Filters for Mini-Mite PLATINUM™ ONLY. These Turbine filters fit the Mini-Mite PLATINUM™ Turbines only. These Mini-Mite PLATINUM™ filters (7224-2) are available in a 2-pack and have the shape of a hand, rather than a square. Please Note: For previous model square shape Mini-Mite filters, please see part #4009-2 #5029 Q-Turbine Filter Turbine filter fits all Q-Series Turbines. Always ensure that upon installation, the Filter fills the whole Filter Enclosure.

Use something like a screwdriver to lever the Filter into position. Windows 95 Bootable Cd Free Download. Please note* the Turbine does not have to be taken apart to remove or replace the Filter. This Filter is a friction fit – it can be replaced in seconds.